★ 77 device pages approved★ 764 sources cited★ Every fact links to its source★ Send us your build log★ No ads. Some part links may earn us a commission.★ 77 device pages approved★ 764 sources cited★ Every fact links to its source★ Send us your build log★ No ads. Some part links may earn us a commission.
mods for old iconic tech · est. 2026
0000080devices tracked

Home › Devices › Nintendo › Nintendo 2DS

[ device photo ]CUSTOM FW!

NINTENDO · HANDHELD CONSOLE · 2013

Nintendo 2DS

Also called: 2DS · FTR-001 · Old 2DS

✔ APPROVEDChecked fact by fact · last checked 2026-11-16 · 9 sources · 1 item(s) unverified

The original Nintendo 2DS (FTR-001, 2013): a rigid slate with a sleep switch instead of a clamshell. One LCD sits behind two windows. It takes the same Luma3DS custom firmware path as other 3DS-family consoles. Common repairs are the CTR-003 battery, Circle Pad, shoulder triggers, screen assembly, and soldered charging port.[4][1][3][5]

7MODS
7WORK
0EXPERIMENTAL
9SOURCES

Which one do I have?

MODELS.TXT
ModelVariantYearHow to tell
FTR-001Nintendo 2DS (original)2013Rigid non-folding body with a physical sleep switch. Launched October 2013. Not the New 2DS XL.[4] unverified
Specs
FormRigid slate; sleep switch instead of closing a shell[4]
ScreenSingle large LCD behind two viewing windows in the plastic frame[4]
BatteryNintendo CTR-003 lithium-ion[4][5]

Mods (7)

⚠ Mod at your own risk. We collect what others have published; we have not tested these mods. Read the safety notes

CTR-003 batteryWorks
BatteryDifficulty: easyOpens caseNo solderingReversible
  • ⚠ Lithium battery Uses or touches a lithium cell. A damaged cell can catch fire.

Open the upper rear panel (two captive Phillips screws) and lift out the CTR-003 pack from the side closest to the outer edge.[5][4]

Parts

  • Nintendo CTR-003 battery Fits — Drops into the battery housing under the upper rear panel.[5]

Good to know

  • Remove the two captive Phillips screws on the upper rear panel to reach the battery.[5]
  • Lift the pack from the side closest to the outside edge.[5]

Guides:Nintendo 2DS Battery Replacement

Luma3DS custom firmwareWorks
SoftwareDifficulty: mediumCase stays closedNo solderingPermanent
  • ⚠ Can brick A mistake can leave the device unable to start.

Open-source custom firmware for the 3DS family, including the 2DS. It needs boot9strap. It adds first-class homebrew support, the Rosalina overlay, LayeredFS asset redirection, and per-game language overrides.[1][3]

Parts

  • SD card, 2 GB to 128 GB Fits with conditions — FAT32 with an MBR partition table. 2 GB minimum for a NAND dump; 200 GB and larger work but are not recommended.[1]

Good to know

  • The 3DS Hacks Guide covers the 2DS along with 3DS, 3DS XL, New 3DS, New 3DS XL, and New 2DS XL.[1]
  • Luma3DS requires boot9strap. After that, install or upgrade by extracting the release archive to the SD card root.[3]
  • Features include homebrew support, Rosalina (default L+Down+Select) for screenshots and screen filters, LayeredFS path redirection, and per-game language overrides.[3]
  • The SD card must be FAT32 with an MBR partition table, capacity 2 GB to 128 GB inclusive.[1]

⚠ Watch out

  • On Windows, WinRAR is known to break custom-firmware archive extracts. Use 7-Zip or the built-in extractor.[1]
  • Cards of 200 GB or larger can cause problems with DS/GBA graphics and custom themes.[1]

Guides:Key Information | 3DS Hacks GuideLuma3DS (LumaTeam)

ntrboot recovery bootWorks
SoftwareDifficulty: mediumCase stays closedNo solderingReversible
  • ⚠ Can brick A mistake can leave the device unable to start.

Boot from a DS flashcart prepared for ntrboot to install boot9strap or recover a console that will not boot. On the original 2DS, use the sleep switch instead of a magnet.[2]

Parts

  • DS flashcart prepared for ntrboot Fits with conditions — A compatible NDS/DSi-era flashcart flashed for ntrboot. Hardware only.[2]

Good to know

  • ntrboot needs a compatible cartridge (normally a flashcart). Many NDS/DSi-era carts can be repurposed.[2]
  • Other 3DS-family models use a small magnet to enter sleep during the button combo. The original 2DS uses its sleep switch instead.[2]
  • The path can install boot9strap (ntrboot) even when the console will not boot normally.[2]

Guides:ntrboot | 3DS Hacks Guide

Circle Pad (joystick)Works
Buttons & inputDifficulty: mediumOpens caseNo solderingReversible

Replace the analog Circle Pad. The cover pops off; the module uses a flat flex into a ZIF connector on the board.[7]

Good to know

  • The joystick cover detaches with little force.[7]
  • The analog module connects with a flat flexible ribbon into a ZIF connector.[7]

Guides:Nintendo 2DS Joystick Replacement

L/R trigger buttonsWorks
Buttons & inputDifficulty: mediumOpens caseNo solderingReversible

Replace the shoulder triggers. They sit in external channels with small springs.[9]

Good to know

  • Pull the trigger button away from the device to remove it.[9]

Guides:Nintendo 2DS Trigger Button Replacement

Screen assemblyWorks
ScreenDifficulty: hardOpens caseNo solderingReversible

Replace or clean the single dual-window LCD. Access means removing the rear case, battery, and motherboard, and unplugging several ribbon cables.[6][4]

Good to know

  • The iFixit guide shows how to reach the screen for repair and cleaning.[6]
  • Internally the 2DS uses one large LCD divided into two windows by the plastic frame.[4]

Guides:Nintendo 2DS Screen Replacement

Charging portWorks
ChargingDifficulty: hardOpens caseFine solderingReversible
  • ⚠ Soldering Needs a soldering iron. Heat can lift pads and burn skin.

Replace a broken proprietary charging connector. It is surface-soldered to the motherboard power traces.[8]

Special tools: soldering iron, Triangle 3 screwdriver

Good to know

  • The iFixit guide covers replacing a broken or damaged charging port on the 2DS.[8]
  • The connector is soldered directly to the board; the guide calls for a soldering iron.[8]

Guides:How to replace the Nintendo 2DS charging port

Sources (9)

SOURCES.TXT