★ 77 device pages approved★ 764 sources cited★ Every fact links to its source★ Send us your build log★ No ads. Some part links may earn us a commission.★ 77 device pages approved★ 764 sources cited★ Every fact links to its source★ Send us your build log★ No ads. Some part links may earn us a commission.
mods for old iconic tech · est. 2026
0000080devices tracked

Home › Devices › Sony › PSP-2000 (Slim)

[ device photo ]CUSTOM FW!

SONY · HANDHELD CONSOLE · 2007

PSP-2000 (Slim)

Also called: PSP Slim · PSP Slim & Lite · PSP 2000

✔ APPROVEDChecked fact by fact · last checked 2026-11-16 · 8 sources

Sony's slimmer PSP-2000 with a 4.3-inch 480×272 screen, 64 MB RAM, and a video-out port. ARK-4 custom firmware can install permanently via cIPL. The battery is user-swappable. Boards that Pandora batteries cannot unbrick can be recovered with Baryon Sweeper. Stock LCD replacement is documented.[8][6][2][7]

6MODS
6WORK
0EXPERIMENTAL
8SOURCES

Which one do I have?

MODELS.TXT
ModelVariantYearHow to tell
PSP-2000Slim & Lite2007Slimmer and lighter than the PSP-1000. Has a video-out port. 64 MB RAM.[1][8]
Specs
Screen4.3-inch TFT, 480×272[8]
RAM64 MB[8]

Mods (6)

⚠ Mod at your own risk. We collect what others have published; we have not tested these mods. Read the safety notes

Replace the batteryWorks
BatteryDifficulty: easyCase stays closedNo solderingReversible
  • ⚠ Lithium battery Uses or touches a lithium cell. A damaged cell can catch fire.

Open the rear battery door and swap the lithium-ion pack. No tools are listed.[2]

Parts

  • PSP-2000 battery Fits — User-replaceable pack under the rear battery door. The guide lists a Sony PSP 2000/3000 battery.[2]

Good to know

  • Place the PSP face down with the UMD drive up, open the battery door, and lift out the pack.[2]

Guides:PSP 2000 Battery Replacement

ARK-4 custom firmwareWorks
SoftwareDifficulty: mediumCase stays closedNo solderingPermanent
  • ⚠ Can brick A mistake can leave the device unable to start.

Modern custom firmware for every PSP model. cIPL makes it permanent with enhanced brick protection. Installs from official firmware or an existing 6.61 PRO or ME setup. Adds homebrew and plugin support.[6]

Good to know

  • ARK-4 supports the PSP and Vita ePSP. It includes homebrew and plugin support compatible with legacy 1.50 software.[6]
  • New cIPL works on all PSP models for permanent custom firmware with enhanced brick protection.[6]
  • Despertar del Cementerio version 10 is included to unbrick a PSP.[6]
  • Installation paths cover official firmware and existing 6.61 PRO or ME installs.[6]

Guides:ARK-4 custom firmware (PSP-Archive)

Baryon Sweeper unbrickWorks
RepairDifficulty: hardOpens caseBasic solderingReversible
  • ⚠ Soldering Needs a soldering iron. Heat can lift pads and burn skin.
  • ⚠ Can brick A mistake can leave the device unable to start.

Hardware service-mode recovery for late PSP-2000/3000 boards that the classic Pandora battery could not reach. Uses a USB-TTL adapter and small parts to emulate the battery Syscon handshake.[7]

Special tools: USB-TTL converter, soldering iron or breadboard

Good to know

  • Baryon Sweeper unbricks PSP-2000 and PSP-3000 in the style of a Pandora battery for boards that need a modern service-mode path.[7]
  • A typical build uses a USB-to-TTL converter (an Arduino with RESET tied to GND works), logic parts, and resistors; soldering or a breadboard is expected.[7]

Guides:Baryon Sweeper lets you unbrick PSP 2000/3000

Replace the LCDWorks
ScreenDifficulty: hardOpens caseNo solderingReversible

Swap the stock TFT panel. The front bezel pries off; the guide shows two ribbon cables to disconnect.[3]

Good to know

  • Gently pry the front bezel away with a PSP opening tool, then disconnect the two display ribbons.[3]

Guides:PSP 2000 Display Replacement

Analog stick, D-pad, and face buttonsWorks
Buttons & inputDifficulty: mediumOpens caseNo solderingReversible

Fix stick drift and dirty button pads. The stick pops off its mount, and the D-pad and action keys can be wiped at the contact points.[5]

Good to know

  • You can wipe the connection points of the D-pad and action keys.[5]
  • The analog stick pulls up and pops off, and the connection point where it meets the PSP should be wiped too.[5]

Guides:PSP 2000 Analog Stick, D-pad and Action Keys Replacement

Front casingWorks
CaseDifficulty: mediumOpens caseNo solderingReversible
  • ⚠ Permanent change Cuts, drills or glues the device. You cannot undo it.

Replace a scratched or broken front faceplate. Seven Phillips screws hold the shell; a 5 mm screw sits under the warranty sticker in the battery bay.[4]

Good to know

  • Removing one screw requires peeling the warranty sticker in the battery compartment.[4]

⚠ Watch out

  • Removing the warranty sticker may void the warranty.[4]

Guides:PSP 2000 Front Casing Replacement

Sources (8)

SOURCES.TXT