Home › Devices › Texas Instruments › Speak & Math
TEXAS INSTRUMENTS · CALCULATOR · 1980-1981
Speak & Math
Also called: Speak and Math · Speak & Maths · TI Speak & Math
TI talking math toy with a membrane keypad and VFD. The main hardware mod is circuit bending the speech oscillator (pitch ribbon or pot); MIDI retrofit kits and seller-built glitch/loop units also exist.[1][3][9]
Which one do I have?
Specs
Mods (3)
⚠ Mod at your own risk. We collect what others have published; we have not tested these mods. Read the safety notes
Pitch-control ribbon (ThinPot)Works
- ⚠ Soldering Needs a soldering iron. Heat can lift pads and burn skin.
- ⚠ Permanent change Cuts, drills or glues the device. You cannot undo it.
Wire a 10k linear SoftPot/ThinPot and a few resistors to the speech-chip oscillator so finger position changes voice pitch in real time.[3][4][8]
Special tools: Soldering iron, File (case cutout)
Parts
- 10k linear ThinPot / SoftPot Fits — Plus ~4.7k, 20k, and 1k resistors in the Structables/Instructables wiring. A series 1k limits short-circuit current if both SoftPot ends are pressed.[3]
Good to know
- A variable resistor on the oscillator changes speech pitch; start speech, then slide along the strip.[3][4]
- The RCOSC pin is extremely sensitive to stray capacitance; clocking above ~320 kHz can over-clock and fail the chip erratically. Very low pitch (~50 kHz) can shut the toy off.[3]
- The author cut and filed the case for the ribbon and fixed it with epoxy.[3]
⚠ Watch out
- Do not leave the pitch too high for long; that can burn out the circuit.[8]
Pitch / glitch / loop circuit bendsWorks
- ⚠ Soldering Needs a soldering iron. Heat can lift pads and burn skin.
- ⚠ Permanent change Cuts, drills or glues the device. You cannot undo it.
Add pots and switches for pitch, glitch, and loop. The Casper diagrams for Speak & Spell are a starting point; sellers show tone oscillators, theremin cells, and touch pads on Math units.[8][5][6][7][10]
Good to know
- Pitch base method uses a ~100k pot; peak buffers matter, especially on the high end. Hold/loop can be a switch alone. Values often need tweaking per model.[8]
- A Math bender reported sticking with pitch, glitch, and loop using 1k links and 20–50k limiting resistors on the pitch pot.[8]
- Bent sale units commonly add glitch/loop switches, pitch knobs, brass touch contacts, opto theremin pitch, and 1/8" or 1/4" outputs that mute the speaker.[5][6][7] unverified
MIDI IN retrofit kitDiscontinued
- ⚠ Soldering Needs a soldering iron. Heat can lift pads and burn skin.
- ⚠ Permanent change Cuts, drills or glues the device. You cannot undo it.
A 2006 Highly Liquid MIDISpeak kit added MIDI IN to Speak & Math (and Spell/Read) to trigger words and effects.[9]
Good to know
- Make: described a MIDISpeak kit that adds a standard MIDI IN port to Speak & Spell, Speak & Read, or Speak & Math.[9]
Guides:No guide found yet.
Sources (10)
- wiki Speak & Math - Wikipedia · 2026-11-16
- blog Texas Instruments Speak & Math · 2026-11-16
- docs Speak and Maths Circuit Bend - Pitch Control Ribbon · 2026-11-16
- news Circuit Bending a Vintage Speak & Math · 2026-11-16
- blog CIRCUIT BENT SPEAK & MATH · 2026-11-16
- blog Circuit Bent Modified Speak & Spell Math · 2026-11-16
- blog Circuit Bent Texas Instruments Speak and Math · 2026-11-16
- forum CASPER Diagrams for Speak & Spell Circuit Bending · 2026-11-16
- news MIDISpeak: Speak & Spell MIDI Kit · 2026-11-16
- forum Fun Speak & Math Circuit Bending · 2026-11-16