★ 132 device pages approved★ 1511 sources cited★ Every fact links to its source★ Send us your build log★ No ads. Some part links may earn us a commission.★ 132 device pages approved★ 1511 sources cited★ Every fact links to its source★ Send us your build log★ No ads. Some part links may earn us a commission.
mods for old iconic tech · est. 2026
0000138devices tracked

Home › Devices › Texas Instruments › Speak & Spell

[ device photo ]NEW!

TEXAS INSTRUMENTS · OTHER · 1978-1992

Speak & Spell

Also called: Speak and Spell · TI Speak & Spell · Dictée Magique

✔ APPROVEDChecked fact by fact · last checked 2026-11-16 · 16 sources · 1 item(s) unverified

Classic TI talking spelling toy and a classic circuit-bending target. Common work is opening the case for pitch/hold/loop bends, repairing corroded battery contacts, cleaning dead keypads, and (historically) a MIDISpeak MIDI IN kit.[13][15][2][10][6]

6MODS
5WORK
0EXPERIMENTAL
16SOURCES

Which one do I have?

MODELS.TXT
ModelVariantYearHow to tell
Speak & SpellOriginal (1978–1992)1978Original run 1978–1992. Regional units change graphics, colour, and jack placement; French Dictée Magique can have different bend points.[11][13][16]
Speak & Spell 2019Basic Fun / Kahootz remake20193 AA cells, segmented LCD, no removable cartridges. Keypad is lightly adhesive and can be reseated.[11][13][12]
Specs
Speech chipTMS5100 (internally TMC0280), first DSP IC for speech generation[14]
KeyboardRaised buttons originally; 1980 redesign used a membrane keypad. Pressing more than 3 keys in one row can ghost odd sounds unmodded.[13]
DisplayVacuum fluorescent on originals; 2019 remake uses segmented LCD and no cartridges[13][11]

Mods (6)

⚠ Mod at your own risk. We collect what others have published; we have not tested these mods. Read the safety notes

Open the caseWorks
RepairDifficulty: easyOpens caseNo solderingReversible15 min

Remove two Phillips screws and release the four catches to reach the PCB, speaker, and battery holder — needed before bends or contact repairs.[9]

Special tools: Phillips screwdriver, Spudgers

Good to know

  • Flip the toy keypad-down, remove two Phillips screws, then release the catches with spudgers. This takes force.[9]

Guides:Disassembling Speak And Spell Case

Replace corroded battery contactsWorks
BatteryDifficulty: mediumOpens caseNo solderingReversible1 hr

Alkaline leaks eat the metal clips and series bus strip. Clean what you can and fabricate or fit new contacts.[10]

Parts

  • Keystone 209 battery contacts Fits with conditions — Commenter suggestion: packs of five, four needed. Not stock-checked.[10]

Good to know

  • Alkaline cells leak and corrode metal parts; the series bus strip between battery pairs often fails.[10]
  • Aluminium foil is too weak as a lasting fix; scrap-metal clips or Keystone-style contacts work better.[10]

Guides:Speak And Spell Battery Contacts Replacement

Clean / reseat keypad contactsWorks
Buttons & inputDifficulty: easyOpens caseNo solderingReversible15-30 min

Dead or wrong-letter keys are often dirty contacts or a lifted membrane. Clean and reseat before replacing the pad.[12]

Good to know

  • When keys stop responding, inspect and clean the keyboard contacts.[12]
  • On the 2019 remake, reseating the lightly adhesive keypad fixed wrong-letter keys.[12]

Guides:SOLVED: Touch keys not responding - Speak And Spell

Circuit bending (pitch, hold, loop)Works
AudioDifficulty: hardOpens caseBasic solderingPermanent1-4 hr
  • ⚠ Soldering Needs a soldering iron. Heat can lift pads and burn skin.
  • ⚠ Permanent change Cuts, drills or glues the device. You cannot undo it.

Wire pots and switches for pitch, hold, and loop using Casper-style diagrams. Match points to your board revision; French and other regional boards can differ.[2][3][15][4][1][5][16]

Good to know

  • Casper diagrams cover pitch base (100k pot), high-end buffers, and optional hold/loop switches. Speak & Spell and Speak & Math share the same general board family aside from panel and voice.[2][3]
  • Only the correct pitch points for each board version work. Turning pitch too high for too long can burn the circuit.[2]
  • A 2010 photo tutorial wires bend switches, a pitch pot/switch, and LEDs (each LED needs its own resistor).[15]
  • Circuitbenders recommends Speak & Spell as a first bend — hard to kill unless you mess with the power supply board. Mono 1/4" or 1/8" jacks are common for line out.[4]

⚠ Watch out

  • Wrong-voltage AC adapters have burnt units. Do not connect house current to your body while probing.[11][7][8]

Guides:CASPER Diagrams for Speak & Spell Circuit BendingHow to circuit bend a Speak and SpellCasper Electronics Speak&Spell Bending (archive)

Repair burnt power / VFD boardWorks
RepairDifficulty: hardOpens caseBasic solderingReversible1-2 hr
  • ⚠ Soldering Needs a soldering iron. Heat can lift pads and burn skin.

A wrong adapter can crack TO-92 transistors on the display power board. Replace the damaged pair; battery vs adapter behaviour may still need tuning afterward.[8]

Good to know

  • A wrong adapter left a burn mark and a cracked TO-92; both transistors in the pair were replaced.[8]
  • After that repair the unit ran from AC but not batteries until further component changes for weaker cells.[8]

Guides:Silent Speak And Spell Gets Its Voice Back

Add MIDI INDiscontinued
ConnectivityDifficulty: mediumOpens caseBasic solderingPermanent1-2 hr
  • ⚠ Soldering Needs a soldering iron. Heat can lift pads and burn skin.
  • ⚠ Permanent change Cuts, drills or glues the device. You cannot undo it.

2006 Highly Liquid kit added MIDI IN to Speak & Spell family toys to trigger sounds.[6]

Good to know

  • Kit works with Speak & Spell, Speak & Read, Speak & Math, and non-English versions.[6]

Guides:No guide found yet.

Sources (16)

SOURCES.TXT