Home › Devices › Tecsun › Tecsun PL-680
TECSUN · RADIO · 2015
Tecsun PL-680
Also called: PL-680 · PL680
Portable HF/VHF receiver closely related to the PL-660, with four AA cells and built-in NiMH charging. Documented board work disables soft mute, adds an LW/MW external-antenna path, and trims frequency with pot adj1391.[4][1][2][9]
Which one do I have?
Specs
| Coverage | 0.1–30 / 76–108 / 118–137 MHz[9] |
| Power | Four AA cells, or 6 V DC barrel (centre negative). Built-in charging for NiMH cells only[9][3][7][12] |
| Antennas | Built-in telescopic whip and ferrite bar; 3.5 mm external jack. Front-end diodes D4/D2 clip large signals on the external path[9][5] |
| Memory | Sources disagree: 1900 (RigPix), 2000 (owner review feature list), or 600 (RigReference)[9][7][10] |
| Audio out | No line-out jack; selectable stereo output[4][8] |
Mods (3)
⚠ Mod at your own risk. We collect what others have published; we have not tested these mods. Read the safety notes
Disable soft muteWorks
- ⚠ Soldering Needs a soldering iron. Heat can lift pads and burn skin.
- ⚠ Permanent change Cuts, drills or glues the device. You cannot undo it.
Two joints to make and a path to scratch on the board near the side tone switch. After the change, that switch turns muting on and off.[1]
Good to know
- Rolf Snijder made the same soft-mute modification on the PL-680 that many owners did on the PL-660.[1]
- Method: make the two joints shown and scratch a path on the print near the switch.[1]
- After the mod, the side-panel tone switch turns muting on and off. One builder leaves it on for FM and off for LW, MW, and SW.[1]
Guides:Tecsun PL-680: Rolf touts enhanced performance using PL-660 mod
External antenna on LW/MWExperimental
- ⚠ Soldering Needs a soldering iron. Heat can lift pads and burn skin.
- ⚠ Permanent change Cuts, drills or glues the device. You cannot undo it.
Add a single capacitor so LW and MW work on an active loop while the internal ferrite still works. FM can get weaker.[2][5][7]
Parts
- 560 pF capacitor Fits with conditions — Value from one build report only; no second source confirmed it.[2]
Good to know
- One builder added a 560 pF capacitor; LW and MW then worked on an active loop and the internal ferrite still worked.[2]
- FM reception got weaker after the change.[2]
- External antenna path already has diodes D4 and D2 that clip signals above about 0.7 V peak. Larger antennas may need more protection.[5]
⚠ Watch out
- An outdoor antenna can overload the front end at some frequencies.[7]
Guides:Rolf's PL-680 modification allows external antenna on LW and MW
Frequency trim (adj1391)Experimental
A pot labelled adj1391 in the right corner corrects about 1 kHz of frequency offset.[1][6][11]
Good to know
- Frequency adjust is with the pot adj1391 in the right corner of the board.[1]
- Early units can show about 1 kHz display offset; the importer called ±0.5 kHz (1 kHz on the LCD) within tolerance. Only the PL-880 was said to have a special MW calibration function at that time.[6]
- A May 2017 sample with old firmware could not use MW/SW calibration. Kaito reported a hidden FM calibration function that was not tested in that write-up.[11]
Guides:Tecsun PL-680: Rolf touts enhanced performance using PL-660 mod
Sources (12)
- blog Tecsun PL-680: Rolf touts enhanced performance using PL-660 mod · 2026-11-16
- blog Rolf's PL-680 modification allows external antenna on LW and MW · 2026-11-16
- news The Tecsun PL-680: A new portable in the works? · 2026-11-16
- blog A review of the Tecsun PL-680 with reader survey results · 2026-11-16
- blog Mehdi discovers ESD protection in the Tecsun PL-680 · 2026-11-16
- news Tecsun PL-680: SSB display inaccuracy · 2026-11-16
- blog TECSUN PL-680 QUICK REVIEW · 2026-11-16
- blog First Impressions: Tecsun PL-680 Receiver · 2026-11-16
- docs RigPix Database - Tecsun PL-680 · 2026-11-16
- wiki Tecsun PL-680 receiver specs · 2026-11-16
- blog N9EWO Reviews: Tecsun PL-660 / PL-680 / PL880 · 2026-11-16
- shop USB to 6V DC Voltage converter for Tecsun Radios · 2026-11-16