★ 231 device pages approved★ 2829 sources cited★ Every fact links to its source★ Send us your build log★ No ads. Some part links may earn us a commission.★ 231 device pages approved★ 2829 sources cited★ Every fact links to its source★ Send us your build log★ No ads. Some part links may earn us a commission.
mods for old iconic tech · est. 2026
0000237devices tracked

Home › Devices › Texas Instruments › TI-83 Plus

[ device photo ]NEW!

TEXAS INSTRUMENTS · CALCULATOR

TI-83 Plus

Also called: TI-83+ · 83 Plus · TI-83 Plus Silver Edition · TI-83+ SE

✔ APPROVEDChecked fact by fact · last checked 2026-11-17 · 19 sources · 3 item(s) unverified

Z80 graphing calculator with flash apps and four AAA cells plus a CR1616 backup. Common work is shell apps (Doors CS, MirageOS), KnightOS as a full OS swap, battery and key repairs, and LED or EL backlights.[1][3][15][12][17]

10MODS
10WORK
0EXPERIMENTAL
19SOURCES

Which one do I have?

MODELS.TXT
ModelVariantYearHow to tell
TI-83PLUSTI-83 Plus (base)—Printed as TI-83 Plus. Four AAA + backup cell. Assembly programs written for the original TI-83 will not run without modification.[1][3] unverified
TI-83PLUS-SETI-83 Plus Silver Edition—Printed as TI-83 Plus Silver Edition. 15 MHz Z80, 128 KB RAM (24 KB user), 1.5 MB flash. Discontinued in favour of the TI-84 Plus line. KnightOS also supports it.[4][14] unverified
Specs
CPU (base)8 MHz Z80 running at 6 MHz[3]
Memory (base)32 KB RAM (24 KB user), 160 KB flash archive/apps[1][3]
Display8 lines × 16 characters, black and white[1]
PowerFour AAA plus lithium backup (CR1616) that protects RAM during main-battery changes[1][5]

Mods (10)

⚠ Mod at your own risk. We collect what others have published; we have not tested these mods. Read the safety notes

Replace backup battery (CR1616)Works
BatteryDifficulty: easyCase stays closedNo solderingReversible5 min
  • ⚠ Lithium battery Uses or touches a lithium cell. A damaged cell can catch fire.
  • ⚠ Data loss Can erase what is on the device. Back up first.

Swap the coin cell that keeps RAM alive when the AAA pack is out. About five minutes; do not remove AAA and lithium together.[5][2][1]

Parts

  • CR1616 lithium coin cell Fits — Spring-loaded; can pop out when pried. Per TI, replace all four AAA cells together, or replace only the lithium cell.[5][2]

Good to know

  • The backup battery powers the calculator so information is not lost when the AAA cells are removed.[5][1]
  • TI says replace all four AAA (or AA) at once, or replace only the lithium cell — removing both types at once can erase memory.[2]
  • Steps: remove AAA cells, unscrew one 5 mm Phillips cover, pry out the spring-loaded CR1616 with a plastic tool.[5]

Guides:TI-83 Plus Backup Battery Replacement

Doors CS shellWorks
SoftwareDifficulty: noneCase stays closedNo solderingReversible15-30 min
  • ⚠ Data loss Can erase what is on the device. Back up first.

Install Doors CS for a desktop GUI that runs BASIC, ASM, MirageOS, Ion, and nostub programs with nested folders.[15]

Good to know

  • Doors CS 7.4 is a shell and GUI for TI graphing calculators that runs BASIC, ASM, MirageOS, Ion, and nostub programs with nested folders.[15]
  • It includes a CALCnet networking library for communication and multiplayer gaming.[15]

Guides:No guide found yet.

MirageOS flash shellWorks
SoftwareDifficulty: noneCase stays closedNo solderingReversible15 min
  • ⚠ Data loss Can erase what is on the device. Back up first.

Flash Application shell for the TI-83 Plus with built-in features for users and assembly programmers.[16]

Good to know

  • MirageOS is a Flash Application shell for the TI-83 Plus with many built-in features for users and assembly programmers.[16]

Guides:No guide found yet.

KnightOS custom OSWorks
SoftwareDifficulty: mediumCase stays closedNo solderingReversible30-60 min
  • ⚠ Can brick A mistake can leave the device unable to start.
  • ⚠ Data loss Can erase what is on the device. Back up first.

Replace TI-OS with open-source KnightOS (with a package manager). Erases RAM and the TI-OS archive; no real graphing math in KnightOS.[12][14][13]

Good to know

  • KnightOS is a third-party open-source OS for TI calculators; it officially supports the TI-83 Plus and TI-83 Plus Silver Edition (also TI-73 / TI-84 Plus / SE).[14][13]
  • Installing KnightOS erases RAM and the TI-OS Archive.[12]
  • KnightOS has no math or graphing support past a simple four-operation calculator.[12]
  • Install path: check boot code, remove a battery, hold DEL, send the OS upgrade with TI-Connect or TiLP. Boot code 1.03 and newer block unsigned OS installs — workarounds are on the download page.[12]
  • TI-OS can be reinstalled from TI's own download.[12]

Guides:Download · KnightOS

Keyboard mat or key replacementWorks
Buttons & inputDifficulty: mediumOpens caseNo solderingReversible30-60 min

Clean or replace the rubber contact mat when keys feel dead; swap individual cracked keys with tweezers after a full teardown.[10][11]

Special tools: T6 screwdriver, tweezers

Good to know

  • The keyboard mat makes contact with the motherboard; if keys work poorly, clean the contacts or replace the mat.[10]
  • Single cracked keys are removed with tweezers one at a time after the case is open.[11]

Guides:TI-83 Plus Keyboard Mat ReplacementTI-83 Plus Individual Keys Replacement

Back case replacementWorks
CaseDifficulty: mediumOpens caseNo solderingReversible3 min

Swap a cracked rear shell. Six T6 screws; pry apart in the protective-cover track.[6]

Special tools: T6 screwdriver

Good to know

  • The back case is held by six 7.5 mm T6 screws; the halves pry apart in the protective-cover track.[6]

Guides:TI-83 Plus Back Case Replacement

Reflow glitchy LCD ribbonsWorks
RepairDifficulty: mediumOpens caseNo solderingReversible50 min

Missing lines on the display are often fixed by gently heating and pressing the ribbon cables with a low heat gun.[8]

Special tools: heat gun (lowest setting)

Good to know

  • Applying heat and pressure to the ribbon cables can restore missing lines.[8]
  • Use the lowest heat-gun setting (about 150 degrees) and heat evenly for about five seconds, then press with a plastic tool.[8]

Guides:How to Repair a Glitchy TI-83 Plus Screen

Screen and motherboard replacementWorks
ScreenDifficulty: hardOpens caseNo solderingReversible10-15 min

The LCD is tethered to the motherboard, so both must be replaced together. Keep the face plate face-down so keys do not fall out.[7]

Good to know

  • The screen is tethered to the motherboard, so both items must be replaced at the same time.[7]
  • Keep the face plate face-down while the screen is loose to prevent the keys from falling out. Eight 5 mm Phillips #00 screws hold the motherboard.[7]

Guides:TI-83 Plus Motherboard & Screen Replacement

Link (I/O) port replacementWorks
ConnectivityDifficulty: hardOpens caseFine solderingReversible1-2 hr
  • ⚠ Soldering Needs a soldering iron. Heat can lift pads and burn skin.

Replace a broken 2.5 mm link jack with a genuine SMD port or a generic 3-pole jack and jumper resistors.[9]

Good to know

  • Pads are lifted with heat; fit a genuine 2.5 mm SMD port or wire a generic 3-pole headphone jack with two jumper resistors.[9]
  • The community guide author disclaims expertise and calls some methods hacky.[9] unverified

Guides:TI-83 Plus IO Port Replacement

LED or EL backlightWorks
ScreenDifficulty: hardOpens caseBasic solderingPermanent2-4 hr
  • ⚠ Soldering Needs a soldering iron. Heat can lift pads and burn skin.
  • ⚠ Permanent change Cuts, drills or glues the device. You cannot undo it.

Add LEDs behind a Plexiglas diffuser (or an EL panel) and a microswitch. Delicate screen-plate work with solvent and cyanoacrylate.[17][18][19]

Good to know

  • A TI-83 Plus build separates the screen plate with a blade and ether, then adds a Plexiglas diffuser and LEDs behind the screen with a momentary microswitch (case wall thinned for the switch).[17]
  • The calculator is supplied with 6 V max from alkaline batteries; check LED diode specs before wiring.[17]
  • On the Silver Edition, four to six bright LEDs were suggested as enough; EL panels behind the screen gave the best results in forum experience.[18][19]

⚠ Watch out

  • Ether solvent is highly volatile; cyanoacrylate glue tubes are toxic — use only enough to hold the LEDs. Intended for experienced hardware builders.[17]

Guides:Backlighting the TI 83+

Sources (19)

SOURCES.TXT