★ 141 device pages approved★ 1634 sources cited★ Every fact links to its source★ Send us your build log★ No ads. Some part links may earn us a commission.★ 141 device pages approved★ 1634 sources cited★ Every fact links to its source★ Send us your build log★ No ads. Some part links may earn us a commission.
mods for old iconic tech · est. 2026
0000147devices tracked

Home › Devices › Texas Instruments › TI-89 Titanium

[ device photo ]NEW!

TEXAS INSTRUMENTS · CALCULATOR

TI-89 Titanium

Also called: TI-89T · 89 Titanium · HW3

✔ APPROVEDChecked fact by fact · last checked 2026-11-16 · 12 sources · 1 item(s) unverified

TI-68k graphing calculator with USB, about 188 KB user RAM and 2.7 MB user flash. Community work covers assembly kernels (HW3Patch / PreOS), the PedroM free OS, an EL-wire backlight, and key or backup-battery repair.[1][3][5][10]

5MODS
4WORK
1EXPERIMENTAL
12SOURCES

Which one do I have?

MODELS.TXT
ModelVariantYearHow to tell
TI-89 TitaniumHW3—Keystroke-compatible with the original TI-89 but with more app memory and a built-in USB port. Community docs call this hardware HW3.[2][3][7]
Specs
User memoryAbout 188 KB user RAM and about 2.7 MB user flash, out of 4 MB flash in total[1][7]
Display160×100 pixels[1]
PowerFour AAA plus a silver oxide backup cell (SR44 / 303 class)[1][11][7]
PortsBuilt-in USB port for computer and unit-to-unit link[1][2]
Hardware / OSCalled HW3; uses AMS 3.x. Official OS is electronically upgradable[7][1][3]

Mods (5)

⚠ Mod at your own risk. We collect what others have published; we have not tested these mods. Read the safety notes

Assembly programs (HW3Patch and PreOS)Works
SoftwareDifficulty: noneCase stays closedNo solderingReversible15-30 min
  • ⚠ Data loss Can erase what is on the device. Back up first.
  • ⚠ Can brick A mistake can leave the device unable to start.

Send and run HW3Patch, then install the PreOS kernel so assembly programs can run. Ghostbuster fixes many older asm programs that break on the Titanium.[3][4][12]

Good to know

  • On a Titanium you must send and run HW3Patch before installing PreOS.[3][4]
  • PreOS is the usual kernel and is described as compatible with all hardware and AMS versions covered by the FAQ.[3]
  • Ghostbuster fixes assembly programs that are incompatible with the TI-89 Titanium; run it on each affected program.[3]
  • After reinstalling the AMS, run HW3Patch again.[3]
  • Universal OS does not support the Titanium and is no longer maintained.[3]

⚠ Watch out

  • Installing more than one kernel can break the calculator.[12]

Guides:The Ultimate TI Calculator FAQ - TI-89, TI-89 Titanium, TI-92 Plus, and Voyage 200

PedroM free OSWorks
SoftwareDifficulty: mediumCase stays closedNo solderingPermanent
  • ⚠ Can brick A mistake can leave the device unable to start.
  • ⚠ Data loss Can erase what is on the device. Back up first.
  • ⚠ Permanent change Cuts, drills or glues the device. You cannot undo it.

Open-source replacement OS for TI-68k calculators. Replaces AMS with a Unix-style shell and an integrated PreOS kernel.[5][6][3]

Good to know

  • PedroM is a complete new OS written from scratch for TI-68k calculators, without proprietary TI AMS code.[5]
  • Compatible hardware listed includes TI-89, TI-89 Titanium, TI-92 Plus, and Voyage 200.[5][6]
  • On the V200 / 89 Titanium, USB is not supported under this free OS.[6]
  • An older FAQ note says PedroM runs most games but has very limited math capabilities.[3]

Guides:No guide found yet.

EL-wire backlightExperimental
ScreenDifficulty: hardOpens caseBasic solderingPermanent1-2 hr
  • ⚠ Permanent change Cuts, drills or glues the device. You cannot undo it.
  • ⚠ Soldering Needs a soldering iron. Heat can lift pads and burn skin.

Open the case, route electroluminescent wire around the screen opening, and power it from an external inverter and battery pack.[10]

Special tools: T6 Torx screwdriver, flathead screwdriver

Good to know

  • The backlight uses EL wire wrapped in a circle around the screen aperture, with ends kept clear of the LCD ribbon cable.[10]
  • Disassembly: remove the batteries and six Torx screws, then pop the plastic case clips.[10]
  • The wire loops out to an inverter and a separate battery pack.[10]

⚠ Watch out

  • Putting an EL strip behind the LCD can rip the LCD ribbon cable. An HW1 test unit ended that way.[10]

Guides:TI-89 Titanium Disassembly and Backlighting

Backup battery swapWorks
BatteryDifficulty: easyCase stays closedNo solderingReversible5-10 min

Replace the silver oxide backup cell that protects RAM while you change the AAA cells.[1][11]

Parts

  • SR44SW or 303 silver oxide cell Fits — Install positive side up under the backup cover.[11][1]

Good to know

  • Four AAA cells power the unit; a silver oxide backup cell protects RAM during a main-battery change.[1][11]
  • Remove the battery cover, unscrew the backup cover, and fit a new SR44SW or 303 cell positive side up.[11]

Guides:TI-89 Titanium batteries Problem

Key / On button replacementWorks
RepairDifficulty: mediumOpens caseNo solderingReversible30 min

Open the case with six T6 screws and replace the power/On key or any other button on the rubber sheet.[8][9]

Special tools: T6 Torx screwdriver

Good to know

  • Remove six T6 screws from the back to open the calculator.[8]
  • The same guide can replace any of the other buttons, not only the On key.[8]
  • Keep the buttons attached to the rubber grommet sheet while peeling it back.[8]

⚠ Watch out

  • After reassembly, check every key. One report had a dead Enter key after putting the unit back together.[9]

Guides:TI-89 Titanium Power Button Replacement

Sources (12)

SOURCES.TXT